keyboard_arrow_right

L298n motor controller

Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

Specification:
Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to to 135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm

Package include:
1x L298N Module

Note:
This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply
DO NOT input voltage to 5v supply interface, however ledding out 5v for external use is available.
When ENA enable IN1 IN2 control OUT1 OUT2
When ENB enable IN3 IN4 control OUT3 OUT4

Buy l298n motor controller from Amazon.com
  • Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
  • High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
  • Large capacity filter capacitance,afterflow protection diode, more stable and reliable.




Buy l298n motor controller from Amazon.com


Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

Specification:
Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to to 135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm

Package include:
2x L298N Module

Note:
This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply
DO NOT input voltage to 5v supply interface, however ledding out 5v for external use is available.
When ENA enable IN1 IN2 control OUT1 OUT2
When ENB enable IN3 IN4 control OUT3 OUT4

Buy l298n motor controller from Amazon.com
  • Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
  • High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
  • Large capacity filter capacitance,afterflow protection diode, more stable and reliable.





Buy l298n motor controller from Amazon.com


WGCD 5 PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Module for Arduino

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

Specification:
Name: Dual H bridge motor driver module
Working mode: H bridge driver (dual)
Main control chip: L298N
Logic voltage: 5 v
The driving voltage: 5 v - 35 v
Logic current : 0mA-36mA
Drive current: 2 a (MAX single bridge)
Storage temperature: - 20 C to 135 C
Max power: 25 w
Weight: 30 g
Size: 43 * 43 * 27 mm

L298N motor controller board module, ideal for Arduino smart car power UNO MEGA R3 Mega2560

Package included:
5 pcs L298N Motor Controller Board Module

Buy l298n motor controller from Amazon.com
  • L298N main driving chip, high drive ability, low calorific value, strong anti-interference capability.
  • Dual H bridge DC stepper module, more stable and higher work efficiency.
  • Size: 43 * 43 * 27 mm/1.69 * 1.49 * 1.06in
  • With built-in 78M05 to supply power, to avoid the damage of voltage regulator chip, when the driving voltage is greater than 12V, please use the external 5V logic power supply.
  • Package: 5 pcs L298N motor controller board module





Buy l298n motor controller from Amazon.com


PChero 2Packs L298N Motor Drive Controller Board Module, Dual H Bridge DC Stepper For Arduino Smart Car Robot

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

Why CHOOSE PChero Motor Drive Controller Board Moduld?

Reason 1: Use L298N for Main Chip

L298N is a kind of high voltage, high current motor driver chip. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V),large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on.Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal, which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit. Using L298N chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well.

Reason 2: Wide Application

PChero L298N Motor Drive Controller Board Mould is ideal for Arduino, Smart Car, Power UNO, MEGA R3, Mega 2560, etc.

Specification -

Chip: L298N

Logic voltage: 5V

Logic current 0mA-36mA

Maximum power: 25W

Drive voltage: 5V-35V

Drive current: 2A(For each DC motor)

Dimension: 43*43*27mm/ 1.69*1.69*1.06 inch

Operating mode: Dual H-bridge driver (can drive 2 DC motors)

Attention -

This module has a built-in 5V power supply, when the driving voltage is 7V-35V, this supply is suitable for power supply.

If driving voltage is more than 12V, please use external 5 Volt logic outputs to switch the H-bridge circuits.

DO NOT input voltage to 5v supply interface, however ledding out 5v for external use is available.

Package Included -

2 x L298N Motor Drive Controller Board Module

Buy l298n motor controller from Amazon.com
  • Package Included - 2pcs L298N Motor Driver Controller Board Modules.
  • Item Size - External size 43*43*27mm / 1.69*1.69*1.06 inch. Drive voltage 5V-35V, high working power to 46V. Large current can reach 3A MAX and continue current is 2A. Power to 25w.(NOTE: To avoid damage, please use an external 5V logic supply when using more than 12V driving voltage.)
  • High Quality - Use L298N as the main driving chip, so the module has such features as strong driving ability, strong anti-interference and low calorific value. And it also use large-capacity filter capacitor and diode with freewheeling protection function, thereby improve the reliability of module.
  • High Efficiency - Dual-channel H-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
  • Easy of Use - No assembly required. This L298N board comes ready to go. Just wire up motors and power, this thing will work wonders.




Buy l298n motor controller from Amazon.com


L298N Dual H Bridge Stepper Motor Driver Controller Board Module for Arduino UNO MEGA R3 Mega2560 Duemilanove Nano Robot(Pack of 2) by IFANCY-TECH

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

Specification:
Chip: L298N
Logic voltage: 5V
Logic current: 0mA-36mA
Storage Temperature: -20 to to 135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm

Buy l298n motor controller from Amazon.com
  • Dual-channel H-bridge driver working mode creates higher working efficiency
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
  • Chip: L298N
  • Large capacity filter capacitance,afterflow protection diode, more stable and reliable


Buy l298n motor controller from Amazon.com


DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

Parameters:
1. Power supply voltage 6.5V-27V, the power cannot be reversed or over 27V, or may burn the module, it is recommended connecting in series 15A fuse in the power input.
2. Dual motor interface, each rated output current 7A, peak current 50A, the motor interface cannot short-circuit, it is recommended connecting in series 15A fuse.
3. The enable signal and forward and reverse control signal control voltage 3-6.5V.
4. Enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ, PWM minimum pulse width 10us.
5. Product dimension: 55x55x16mm 
6. Installation hole diameter: 3mm, noted to prevent short circuit when install the reverse side, you can add insulation pad or copper column to raise the circuit board

Parameters matched:
Motors with rated voltage 24V, identification of rated power 115W or below, and motors with identification of rated current 7A can full work for a long time.

Note: 
1. Drive power cannot be reversed, it is recommended connecting in series 15A fuse in the power interface, the voltage should be between 6.5 - 27V. If over voltage, it may burn the drive module if power on.
2. It is recommended that the rated output current of the power supply be more than 2 times, in case the power supply voltage cannot reach the required input voltage of the motor when it is started, which   may cause pause of the drive module for under voltage protection.
3. Motor interface cannot be short-circuit, or may burn the drive module, it is recommended connecting in series 10A fuse in the motor interface.

Package Including:
1x DC Motor Driver Board

Buy l298n motor controller from Amazon.com
  • DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W.
  • STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time.
  • FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation.
  • PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ.
  • UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module.








Buy l298n motor controller from Amazon.com


Aideepen 5pcs 1.5A 2 Way DC Motor Driver Module Speed Dual H-Bridge Replace Stepper L298N

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

Description:
Motor drive module is ideal for use in battery-powered smart car, toy cars, robots.
Supply voltage 2V 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed.
Each can provide continuous current of 1.5A, peak current up to 2.5A, thermal protection and can be automatically restored.

Product parameters:
The module supply voltage 2V-10V.
Signal input voltage 1.8-7V.
Single Operating current 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA).
Built-in common conduction circuit, when the input pin is left floating, the motor does not malfunction.
Built-in thermal protection circuit with hysteresis effects (TSD), without worrying about motor stall.
Product size: 24.7 * 21 * 5mm (length, width, height), ultra-small size.
The mounting hole diameter: 2 mm.

Precautions:
1. Power positive and negative reversed will certainly cause damage to the circuit.
2. Output is shorted to ground or output short circuit, and the motor stall, the chip will heat protection, but in the near or exceeding 10V voltage and peak current is greater than 2.5A situation can also cause chip burned.

Package Included:
5* Motor drive module

Buy l298n motor controller from Amazon.com
  • Use of imported original chip, built-in low on-resistance MOS switch
  • Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor
  • Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped
  • Minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered
  • Small size, light weight, 0 standby current, is the ideal choice for your car model




Buy l298n motor controller from Amazon.com


L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects Electric Projects

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

L298N Stepper Motor Controller

Specification:
Size: 43*43*27mm/ 1.69*1.69*1.06 inch
Dual H bridge drive (can drive 2 DC motors)
Chip: L298N
Logical voltage: 5V
Drive voltage: 5V-35V
Logic current: 0mA-36mA
Drive current: 2A(For each DC motor)
Weight: 30g
TIMESETL L298N DC Stepper Motor Drive - Usage
Great for Arduino, Smart Car, Power UNO, MEGA R3, Mega 2560, etc
If driving voltage is more than 12V, please use external 5volt logic outputs to switch the H-bridge circuits.

quantity
3 pack L298N Stepper Motor Controller

Buy l298n motor controller from Amazon.com
  • High Quality Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects
  • Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
  • Large capacity filter capacitance,afterflow protection diode, more stable and reliable.
  • Wide Usage Great for for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits






Buy l298n motor controller from Amazon.com


L298N H-bridge Motor Controller, DROK L298N Motor Driver Board DC Dual H Bridge Robot Stepper Motor Regulator and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Duemilanove

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

Parameter:
Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to to 135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm

Product features:
1.L298N as main driver chip makes strong driving ability/small heating/strong anti-interference
2.Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
3.This moduel integrated with one internal 5V power supply, meaning when your driving voltage is 7V-35V,it makes 5V of energy board power supply logically; when 5V of energy board power on, please not input voltage to 5V power supply in interface but you can lead 5V voltage for external usage
Eg: ENA enable IN1 IN2 to control OUT1 OUT2
ENB enable IN3 IN4 to control OUT3 OUT4

Package includes:
1x L298N Module


Buy l298n motor controller from Amazon.com
  • DROK L298N h-bridge motor controller working mode creates higher working efficiency, L298N as main chip, ST corporation production. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability.
  • Our motor regulator board drive voltage is 5V-35V, drive current is 2A, max power is 25W.
  • Large capacity filter capacitance, afterflow protection diode, more stable and reliable.




Buy l298n motor controller from Amazon.com


Honbay L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control & Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Duemilanove Nano Robo

Buy l298n motor controller
Check Price on Amazon
Buy l298n motor controller from Amazon.com

Description:

100Brand New and High Quality
Working mode: H bridge (double lines)
Control chip: L298N
Logical voltage: 5V
Driving voltage: 5V-35V
Logical current: 0mA-36mA
Driving current: 2A (MAX single bridge)
Storage temperature: (-20 C)-(135 C)
Maximum power: 25W
Weight: 27g
Periphery dimension: 43 x 43 x 27mm(L x W x H)

Package Included:
1 X L298N Stepper Drive Controller Board

Buy l298n motor controller from Amazon.com
  • L298N has such characteristics as strong driving ability, low calorific value and strong anti-interference ability
  • L298N as main driver chip makes strong driving ability/small heating/strong
  • Dual-channel H-bridge driver working mode creates higher working efficiency
  • Using large capacity filter capacitor, this module can follow current to protect diodes, and improve the reliability
  • This module can use built-in 78M05 for electric work via a driving power supply part. But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage



Buy l298n motor controller from Amazon.com


L298n motor controller